Mounting Bracket

 

180+ lbs.

 

.30” inches per sec.

Using our mounting brackets will allow you to easily and quickly attach the actuator to various contact points as shown to the left.

All you need to do in order to get your actuator up and running is apply 6-12VDC to the positive (red) and negative (black) wires. You do not need to do anything with the potentiometer wires (Blue, Yellow, White). The potentiometer wires are only needed if you are building a system which requires you to know the exact position of the actuator piston. For normal operation, we recommend purchasing the switch above and wiring the switch according to the schematic.

Feedback Wiring Schematic:
White - 10K Potentiometer Reference
Blue - 10K Potentiometer Wiper (Position Signal) Yellow - 10K Potentiometer Reference

Actuator Wiring for switch 2

Price:

 $9.99

Part:

 275-709

Status:

 

Qty:

DPDT 20A Actuator Switch

12V Servo Actuator in test

6.00”

HDA6-30

43.3 oz.

$129.99

8.00”

HDA8-30

45.1 oz.

$129.99

12.00”

HDA12-30

50.4 oz.

$129.99

Out of Stock Button

 

2.00”

HDA2-30

38.2 oz.

$129.99

 

4.00”

HDA4-30

40.2 oz.

$129.99

Stroke

Part #

Weight

Price

Status

Qty

Buy

10.00”

HDA10-30

47.9 oz.

$129.99

Move up to 180 lbs for under $130! Introducing our all new Heavy Duty 12V Linear Actuators. Now you have the power for those extra large projects. Built in potentiometer can be easily accessed for position feedback but is not necessary for operation. Limit switches at both ends prevent over-run. All aluminum construction with metal drive gears ensure tremendous durability and reliability. We offer them in six stroke lengths from 2 inches up to 12 inches. Extension shaft is .785” diameter. Mounting points are 1/4” diameter and bolt up directly to our optional mounting brackets. 
ROHS and CE listed

X = Center to Center

Stroke

Retracted

Extended

1.96”

7.68”

9.64”

3.93”

9.69”

13.62”

5.90”

11.69”

17.59”

7.87”

13.70”

21.57”

9.94”

15.71”

25.65”

11.81”

17.72”

29.53”

Price:

 $12.99

Part:

 HDM250

Status:

 

Qty:

12V Servo Actuator back with mount
12V Servo Actuator front with mount
Actuator Potentiometer Wire Schematic
Actuator Potentiometer Schematic2

Operating Voltage: 6.0-12 Volts DC
Operating Temperature Range: -20 to +60 Degree C
                              -14.8 to +149 Degrees F
Operating Speed (12V): .30” second at No load
Operating Speed (12V): .20” second at Max load
Dynamic Thrust (12V): 180 lbs. Thrust
Static Load: 500 lbs.
Current Drain (12V): 600mah operating No load
Current Drain (12V): 3200mah operating Max load
Motor Type: 3 Pole Ferrite
Potentiometer: I0K
Gear Type: 4 Metal Gears
Connector Wire Length: 24"
Recommended Fuse: 5amp inline
IP Grade: 2IP 63-total dust protection, water resistant
Duty Cycle: 25% (25% on, 75% off)
Load force: 224.8 lbs
Static load capacity: 517 pounds
Housing Material: Zinc Alloy
IP65 Protection
 

Detailed Specifications

Actuator Mount sm

Aluminum stroke rod and outer tube

Copyright 1999-2012 Robotzone, LLC. - All Rights Reserved
ServoCity is a registered trademark of Robotzone, LLC.

We have the parts for your ideas!
180 lbs. Thrust Linear Actuators
Shopping Cart Button