Detailed Specifications
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 4.8-6.0 Volt Peak to Peak Square Wave
Operating Voltage Range: 4.8-6.0 Volts
Operating Temperature Range: -20° to +60° C (-4°F to +140°F)
Operating Speed (4.8V): 0.19 sec/60° at no load
Operating Speed (6.0V): 0.15 sec/60° at no load
Stall Torque (4.8V): 250oz/in. (18kg.cm)
Stall Torque (6.0V): 333oz/in. (24kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Idle Current Drain (4.8V): 9mA at stop
Idle Current Drain (6.0V): 9mA at stop
Current Drain (4.8V): 220mA/idle and 3.4 amps at lock/stall
Current Drain (6.0V): 300mA/idle and 4.2 amps at lock/stall
Dead Band Width: 1usec
Motor Type: Coreless Carbon Brush
Potentiometer Drive: 6 Slider Indirect Drive
Bearing Type: Dual Ball Bearing MR106
Gear Type: Titanium Gears
Connector Wire Length: 7" (178mm)
Dimensions: 1.57" x 0.78"x 1.45" (40 x 20 x 37mm)
Weight: 2.29oz (65g)
|
|
333 oz-in. |
|
0.15 sec/60° |
*Digital servos do not need to be programmed to operate. They work great right out of the box and purchasing a programmer is not necessary.
Replacing the HS-5955TG, our new premium high speed HS-7955TG Digital Servo has the added benefit of our new G2 second generation programmable digital circuit. This circuit has twice the resolution of our original circuit while adding programmable overload protection. The technology doesn’t stop at the circuit board, with high performance coreless motors, dual ball bearings, bushing supported gear shafts, dual ball bearing output shaft and our Titanium gear train the HS-7955TG will give you everything you need no matter what the demand. We offer the HS-7955TG servo in several configurations, 90° stock rotation, 180° modified rotation, continuous rotation (potentiometer is left outside the servo case) and reverse rotation.
HS-7955TG Hardware Set
Programable Features:
- Dead Band Width
- Direction of Rotation
- Speed of Rotation (slower)
- End Points (up to 180 degrees)
- Neutral Points
- Fail Safe On/Off
- Fail Safe Points
- Resolution (default is set at high)
- Overload Protection (default is off)
This servo can be configured to operate 180° by using any of the following servo programmers:
Hitec HFP-25, HPP-21, HPP-21+
Uses C1 Standard Spline
|
|
|||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
Introductory Sale Price Limited Time Offer!
Hitec Servo Accessories
Click on the picture for further information.
Servo Screws
Servo Hardware
Servo Extensions
Servo Arms
Hitec Casesets
Copyright 1999-2013 Robotzone, LLC. - All Rights Reserved
ServoCity is a registered trademark of Robotzone, LLC.
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Proud Distributor of
