Detailed Specifications
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 4.8-7.4 Volt Peak to Peak Square Wave
Operating Voltage Range: 4.8-7.4 Volts
Operating Temperature Range: -20 to +60 Degree C (-68F to +140F)
Operating Speed (6.0V): 0.21 sec/60° at no load
Operating Speed (7.4V): 0.17 sec/60° at no load
Stall Torque (6.0V): 500oz/in. (36kg.cm)
Stall Torque (7.4V): 611oz/in. (44kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
360 Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Idle Current Drain (6.0V): N/A (Testing Now)
Current Drain (4.8V): N/A (Testing Now)
Current Drain (6.0V): N/A (Testing Now)
Dead Band Width: 1usec
Motor Type: Coreless Carbon Brush
Potentiometer Drive: 6 Slider Indirect Drive
Bearing Type: Dual Ball Bearing MR106
Gear Type: Titanium Gears
Connector Wire Length: 11.81" (300mm)
Dimensions: 1.72" x 0.88"x 1.57" (43.8 x 22.4 x 40mm)
Weight: 2.76oz (78.2g)
|
|
611 oz-in. |
|
0.21 sec/60° |
*Digital servos do not need to be programmed to operate. They work great right out of the box and purchasing a programmer is not necessary.
HS-7980TH Hardware Set
Programable Features:
- Dead Band Width
- Direction of Rotation
- Speed of Rotation (slower)
- End Points (up to 180 degrees)
- Neutral Points
- Fail Safe On/Off
- Fail Safe Points
- Resolution (default is set at high)
- Overload Protection (default is off)
New G2.5 circuit board
Titanium Gears
Titanium Output Spline
Gold-Plated Connector
The "Monster Torque" HS-7980TH is here! Designed to operate on a two cell LiPo Pack. Features our newest high resolution "G2.5" 12 bit generation programmable digital circuit and our indestructible Titanium gears. The
HS-7980TH has the performance and durability you've come to expect from a Hitec servo. The HS-7980TH has been designed for the most demanding hobby applications including the largest aircraft and monster trucks. Featuring a titanic 611oz./in. of torque at 7.4 volts, all this power is harnessed by incorporating the industries first Titanium gears for incredible wear resistance and two strong hardened steel gear pins and axial brass bushing mounted in the servo case. We offer the HS-7980TH servo in several configurations, 90° stock rotation, 180° modified rotation, continuous rotation (potentiometer is left outside the servo case) and reverse rotation. Other features in the HS-7980TH include a 7.4V optimized coreless motor, integrated heat sink case, and a top case with two hardened steel gear pins supported by axial brass bushing.
Note that the HS-7980TH is about 10% larger than a standard servo such as the HS-7950TH.
This servo can be configured to operate 180° by using any of the following servo programmers:
Hitec HFP-25, HPP-21, HPP-21+
Uses C1 Standard Spline
|
|
|||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
Copyright 1999-2012 Robotzone, LLC. - All Rights Reserved
ServoCity is a registered trademark of Robotzone, LLC.
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
