180+ lbs.

 

.30” inches per sec.

All you need to do in order to get your actuator up and running is apply 6-12VDC to the positive (red) and negative (black) wires. You do not need to do anything with the potentiometer wires (Blue, Yellow, White). The potentiometer wires are only needed if you are building a system which requires you to know the exact position of the actuator piston. For normal operation, we recommend purchasing the switch above and wiring the switch according to the schematic.

Feedback Wiring Schematic:
White - 10K Potentiometer Reference
Blue - 10K Potentiometer Wiper (Position Signal) Yellow - 10K Potentiometer Reference

Actuator Wiring for switch 2

Price:

 $9.99

Part:

 275-709

Status:

 

Qty:

DPDT 20A Actuator Switch

6.00”

HDA6-30

43.3 oz.

$129.99

8.00”

HDA8-30

45.1 oz.

$129.99

Out of Stock Button

 

12.00”

HDA12-30

50.4 oz.

$129.99

2.00”

HDA2-30

38.2 oz.

$129.99

4.00”

HDA4-30

40.2 oz.

$129.99

Stroke

Part #

Weight

Price

Status

Qty

Buy

10.00”

HDA10-30

47.9 oz.

$129.99

Move up to 180 lbs for under $130! Introducing our all new Heavy Duty 12V Linear Actuators. Now you have the power for those extra large projects. Built in potentiometer can be easily accessed for position feedback but is not necessary for operation. Limit switches at both ends prevent over-run. All aluminum construction with metal drive gears ensure tremendous durability and reliability. We offer them in six stroke lengths from 2 inches up to 12 inches. Extension shaft is .785” diameter. Mounting points are 5/16” diameter and bolt up directly to our optional mounting brackets. 
ROHS and CE listed

Actuator Potentiometer Wire Schematic
Actuator Potentiometer Schematic2

Operating Voltage: 6.0-12 Volts DC
Operating Temperature Range: -20 to +60 Degree C
-14.8 to +149 Degrees F
Operating Speed (12V): .30” second at No load
Operating Speed (12V): .20” second at Max load
Dynamic Thrust (12V): 180 lbs. Thrust
Static Load: 500 lbs.
Current Drain (12V): 600mah operating No load
Motor Type: 3 Pole Ferrite
Potentiometer: I0K
Gear Ratio: 30:1 Ratio
Gear Type: 4 Metal Gears
Connector Wire Length: 24"
Recommended Fuse: 5amp inline
IP Grade: IP 65 - total dust protection, water resistant
Duty Cycle: 25% (25% on, 75% off)
Housing Material: Zinc Alloy

Detailed Specifications

Aluminum stroke rod and outer tube

Heavy Duty Actuator Schematic

X = Center to Center

Stroke

Retracted

Extended

1.96”

7.68”

9.64”

3.93”

9.69”

13.62”

5.90”

11.69”

17.59”

7.87”

13.70”

21.57”

9.94”

15.71”

25.65”

11.81”

17.72”

29.53”
30-1 gear ratio (HDA) table
12V Servo Actuator in test

Mounting Bracket

Using our mounting brackets will allow you to easily and quickly attach the actuator to various contact points as shown to the left.

Price:

 $12.99

Part:

 HDM250

Status:

 

Qty:

12V Servo Actuator back with mount
12V Servo Actuator front with mount
6391K401 bronze bearings

1/4” Oilite Bushings (pair)

Price:

 $3.49

Part:

 6391K401

Status:

 

Qty:

- 1/4” Shaft Diameter
- 5/16” Outside Diameter
- 3/4” Length

These bushings allow you to run 1/4” shafts through the pivot points of the actuator.

Includes 1/4” ID Bushing

Mounting bracket with bushing

Copyright 1999-2012 Robotzone, LLC. - All Rights Reserved
ServoCity is a registered trademark of Robotzone, LLC.

We have the parts for your ideas!
180 lbs. Thrust Linear Actuators
Shopping Cart Button