Detailed Specifications
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 4.8-6.0 Volt Peak to Peak Square Wave
Operating Voltage Range: 4.8-6.0 Volts
Operating Temperature Range: -20° to +60° C (-4°F to +140°F)
Operating Speed (4.8V): 0.07sec/60° at no load
Operating Speed (6.0V): 0.05sec/60° at no load
Stall Torque (4.8V): 20.83oz/in. (1.5kg.cm)
Stall Torque (6.0V): 26.39oz/in. (1.9kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 600usec
360 Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 2100usec
Idle Current Drain (4.8V): 3mA at stop
Idle Current Drain (6.0V): 3mA at stop
Current Drain (4.8V): 200mA/idle and 2.0 amps at lock/stall
Current Drain (6.0V): 240mA/idle and 3.0 amps at lock/stall
Dead Band Width: 2usec
Motor Type: Carbon Brush
Potentiometer Drive: 6 Slider Indirect Drive
Bearing Type: Dual Ball Bearing MR106
Gear Type: Metal Gears
Connector Wire Length: 7" (178mm)
Dimensions: 1.14" x 0.51"x 1.18" (29 x 13 x 30mm)
Weight: .76oz (21.7g)
|
|
26.39 oz-in. |
|
0.05 sec/60° |
*Digital servos do not need to be programmed to operate. They work great right out of the box and purchasing a programmer is not necessary.
Included servo mounts
Included servo horns and hardware
Standard size servo spline
Absolutely amazing speed is what the all new HSG-5084MG servo is about. The “extreme speed” HS-5084MG Digital Micro Tail Rotor servo is based on the HSG-5083 but utilizes a standard frame rate digital amplifier. Designed to work with most gyros the HSG-5084MG is designed to obtain optimum performance in the T-Rex 400-450, Helimax 400-450 or similar class of electric helis. Not only does the all new HSG-5084MG give you extreme speed, it also offers excellent centering, resolution and durability for those looking to save weight without sacrificing performance. An absolutely perfect choice for smaller airplanes, heli’s, boats, cars, trucks and robots. Incorporating the standard size Hitec spline means that all of your servo horns from standard size Hitec servos work with the HSG-5084MG.
Although the HSG-5084MG is digital, it is not programmable.
This servo can operate 90° when given a pulse signal ranging from 900usec to 2100usec.
A = .51” (12.9mm)
B = .402” (10.2mm)
C = .976” (24.8mm)
E = .264” (6.7mm)
F = .872” (22.15mm)
G = .409” (10.4mm)
H = .772” (19.6mm)
J = 1.565” (39.75mm)
K = .390” (9.9mm)
L = .179” (4.55mm)
M = 1.136” (28.85mm)
X = .140” (3.56mm)
Uses C1 Standard Spline
|
|
|||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
Copyright 1999-2012 Robotzone, LLC. - All Rights Reserved
ServoCity is a registered trademark of Robotzone, LLC.
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
