Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.20sec/60 at no load
Operating Speed (6.0V): 0.17sec/60 at no load
Stall Torque (4.8V): 72oz/in. (5.2kg.cm)
Stall Torque (6.0V): 89 oz/in. (6.4kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8.8mA/idle and 400mA no load operating
Current Drain (6.0V): 9.1mA/idle and 500mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: Ball Bearing
Gear Type: Karbonite Gear
Connector Wire Length: 11.81" (300mm)
Dimensions: 1.57" x 0.78"x 1.49" (39.8 x 19.8 x 38mm)
Weight: 1.59oz. (45g)


 89 oz-in.


 0.17 sec/60

*Digital servos do not need to be programmed to operate. They work great right out of the box and purchasing a programmer is not necessary.

Detailed Specifications

A = .787” (20mm)
B = .539” (13.7mm)
C = 1.319” (33.50mm)
D = .396” (10.05mm)
E = .374” (9.5mm)
F = 1.207” (30.65mm)
G = .463” (11.75mm)
H = 1.08” (28.15mm)
J = 2.087” (53mm)
K = .291” (7.4mm)
L = .176” (4.47mm)
M = 1.581” (40.15mm)
X = .125” (3.18mm)

Standard Servo Schematic 2

The digital wave is now sweeping across the servo world and Hitec is leading the way. The HS-5485HB is Hitec’s second digital standard servo. Adding the digital component to the already great HS-485HB means that the
HS-5485HB is even better. The torque numbers and speed are enhanced from the HS-485HB. The standing torque is nearly 5 times better and the precision has been increased. Being digital means the motor now receives the position signal 300 times per second rather than 30 times per second. This servo can also be programmed using our hand-held servo programmer. Need the servo to travel up to 180 no problem! Need to slow the servo down, no problem! You can do just about anything with Hitec digital servos in combination with the programmer.
Note: The HS-5485HB servo spline is slightly oversized and will be a very snug fit into broached servo accessories. After installed the first time, later assembly will be easier.

Karbonite Spline

The HS-5485HB incorporates strong Karbonite gears and 24T output spline

This servo can be configured to operate 180 by using any of the following servo programmers:
Hitec HFP-25, HPP-21, HPP-21+

Servo Programmability
C1 Hitec Spline2

Click for more information

Uses C1 Standard Spline

Conversion Calculators - Click Here










Hitec Servo Accessories

Click on the picture for further information.

Servo Screws

Servo Hardware

Servo Extensions

Servo Arms

Hitec Casesets

Note: The HS-5485HB servo spline is slightly oversized and will be a very snug fit into broached servo accessories. After installed the first time, later assembly will be easier.

General Servo Information

Rotation direction
Connector types
180 rotation
Continuous rotation

What is a servo?
How servos work
What servo to use
Servo power & speed


Share with friends!

Top Border - We have the parts for your ideas!
Bottom border
Top Border - thin black line
ServoCity-We have the parts for your ideas!
New Products Click Here
Payments we accept
Shop Online or Call
Google Plus
HS-5485HB Servo
ServoCity - Servos & Accessories - Hitec Servos - HS-5485HB Servo -
Servos & Accessories
Motors & Accessories
Servo Controllers
Motor Controllers
Transmitters & Accessories
Pan/Tilt/Roll & Accessories
Camera Accessories
Robots & Accessories
Channel & Brackets
Shafting & Tubing
Hubs, Couplers & Adaptors
Bearings & Bushings
Sprockets & Chain
Pulleys & Belts
Wheels & Tires
Fasteners & Hardware
Batteries & Power Supplies
Wire/Connectors & Access.
Electronics & Accessories
Web Specials
Discounts & Promotions
Contact Us
Project Center

Huge Selection. Low Prices.

Copyright 1999-2015 Robotzone, LLC - All rights reserved.
ServoCity® is a registered trademark of Robotzone, LLC.